一. Strength performance
The strength performance of the valve refers to the ability of the valve to withstand the pressure of the medium. The valve is a mechanical product that bears internal pressure, so it must have sufficient strength and rigidity to ensure long-term use without cracking or deformation.
二. Sealing performance
The sealing performance of a valve refers to the ability of each sealing part of the valve to prevent the leakage of the medium. It is the most important technical performance index of the valve. The valve has three sealing parts: the contact between the opening and closing parts and the two sealing surfaces of the valve seat; the matching place between the packing and the valve stem and the stuffing box; the connection between the valve body and the bonnet. The former leakage is called internal leakage, which is commonly referred to as lax closure, which will affect the ability of Taike valve to cut off the medium. For shut-off valves, internal leakage is not allowed. The latter two leaks are called external leakage, that is, the medium leaks from the inside of the valve to the outside of the valve. Leakage can cause material loss, pollute the environment, and cause accidents in severe cases. For flammable, explosive, toxic or radioactive media, external leakage is not allowed, so Taike valves must have reliable sealing performance.
三, flowing medium
After the medium flows through the valve, pressure loss (the pressure difference between the front and rear of the valve) will occur, that is, the valve has a certain resistance to the flow of the medium, and the medium consumes a certain amount of energy to overcome the resistance of the valve. From the perspective of energy conservation, when designing and manufacturing valves, the resistance of the valve to the flowing medium should be reduced as much as possible.
Hoisting force and hoisting moment Hoisting force and hoisting moment refer to the force or moment that must be applied to the valve to open or close. When closing the valve, it is necessary to form a certain seal specific pressure between the opening and closing parts and the two sealing surfaces of the seat, and at the same time overcome the gap between the valve stem and the packing, the thread between the valve stem and the nut, and the support at the end of the valve stem. The frictional force of other friction parts, therefore, a certain closing force and closing torque must be applied. During the opening and closing process of the valve, the required opening and closing force and opening and closing torque are changed, and the maximum value is at the final instant of closing or opening The initial instantaneous. When designing and manufacturing valves, strive to reduce their closing force and closing torque.
四, opening and closing speed
The opening and closing speed is expressed by the time required for the valve to complete an opening or closing action. Generally, there are no strict requirements on the opening and closing speed of the valve, but some working conditions have special requirements for the opening and closing speed. If some require rapid opening or closing to prevent accidents, some require slow closing to prevent water hammer, etc. This should be considered when selecting the valve type.
五. Action sensitivity and reliability
This refers to the sensitivity of the valve to respond to changes in media parameters. For valves with specific functions such as throttle valves, pressure reducing valves, and regulating valves, as well as valves with specific functions such as safety valves and traps, their functional sensitivity and reliability are very important technical performance indicators.
六, service life
It indicates the durability of the valve, is an important performance index of the valve, and has great economic significance. It is usually expressed in terms of the number of openings and closings that can guarantee the sealing requirements, and it can also be expressed in terms of use time.
In terms of the types of valves used, machinery, metallurgy, petrochemical, chemical, urban construction and other industries have the most types of valves. Especially in the machinery industry, all kinds of valves are basically used. In addition to the machinery industry, butterfly valves are mainly used in petrochemical and metallurgy; diaphragm valves are mainly used in metallurgy, electric power and chemical industry; check valves are mainly used in metallurgy, chemical industry and petrochemical; stop valves are mainly used in petroleum and chemical industry; ball valves are mainly used in petroleum , Chemical industry and metallurgy; regulating valve is mainly used in chemical industry, metallurgy, electric power and food; pressure reducing valve is mainly used in petrochemical, chemical industry and metallurgy.
Post time: Sep-30-2021